SIEMENS

MD Series Networked Power Metering 
Download Page

THIS DOWNLOAD PAGE PROVIDES ACCESS TO IMPORTANT INFORMATION, SOFTWARE TOOLS AND FIRMWARE UPDATES FOR THE MD SERIES POWER METERING PRODUCTS. PLEASE CLICK ON ONE OF THE FOLLOWING METER MODEL TYPES TO BE TAKEN TO THE INTENDED SUPPORT AREA:

MD-BMS, MD-BMED, MD-BM 3-Phase Power Metering Kits
MD-BMS Series MD-BMS_thumb
MD-BMED Series MD-BMED_thumb
MD-BM Series MD-BM_thumb

 

MD-P1, MD-P1D 3-Phase Power Metering Kits
MD-P1 Series MD-BMS_thumb
MD-P1D Series MD-BMED_thumb

 

MD-12HD or MD-48HD Networked Metering Systems
MD-12HD Series MD-12HD-D_thumb  MD-12HD-N_thumb
MD-48HD Series MD-48HD-D_thumb  MD-48HD-P_thumb

 


--------------------------------------------------

MD-BMS, MD-BMED, MD-BM 3-PHASE POWER METERING KITS
READ ME FIRST - MD SERIES POWER METER STARTUP

info-symbol-small IMPORTANT! PLEASE NOTE:

1.  The ViewPoint™ Software tool provided on this CD is not typically required for configuring your new MD series Power Meter for use with the Apogee or other Building Automation Systems. This metering kit, comprised of a meter plus three current transducers (CTs), has been factory-configured with meter setup parameters for the specific CT current ranges that were ordered. 

There are typically no additional user requirements that utilize the ViewPoint™ software to perform any further configuration of the MD series metering kits to support setup or installation.

Please read the power meter installation chapter in the User Manual for the installation and start up instructions. If there is a reason to reconfigure the meter to accept a CT set with a different current range, please consult the appropriate Siemens MD series User Manual noted below.

To download the manual, click on the desired link:
•  Siemens MD-BMS and MD-BMED Series User Manual #125-202
•  Siemens MD-BM User Manual #125-200

2.  The RS-485 network device address for the MD series Power Meters is set only via the rotary address switches on the front left face of the meter. The BACnet/Modbus address cannot be configured with ViewPoint software. See the User Manual for detailed instructions on setting the device address via the front mounted rotary switches. See the MD-BMS and MD-BMED User Manual for instructions regarding the setting of the IP address for the MD-BMED model Ethernet communication. 

3.  If you intend to use the ViewPoint™ software tool with the MD series Power Meters for purposes of data register viewing or for firmware upgrades, please first consult the ViewPoint™ chapter in the User Manuals. 

image WARNING: Improper use of this powerful ViewPoint software tool may result in modifying internal meter setup parameters that could make the power meter inoperative.

Before using this ViewPoint software tool, please read the ViewPoint™ use instructions contained in the Siemens User Manual.  See links above to download the manual.

You may download a copy of this Read Me file by clicking here.

Software and Firmware Downloads
MD-BMS, MD-BMED, MD-BM Series

ViewPoint Software Tool Downloads
•  Read Me
•  4-0-38 ViewPoint MD-Series.exe

MD Series 3-Phase Power Meter Firmware Downloads
To view a log of firmware update history, click here.

Current Firmware (for MD-BMS, MD-BMED Series Meters)
•  Firmware 4-82 MD-BMX.zip

Final Firmware (for Legacy MD-BM Meters - EOL in 2015)
•  Firmware 3-37 MD-BM.zip

--------------------------------------------------

MD-P1, MD-P1D, MD-BM 3-PHASE POWER METERING KITS 
READ ME FIRST - MD SERIES POWER METER STARTUP

info-symbol-small IMPORTANT! PLEASE NOTE:

1.  The ViewPoint™ Software tool provided on this CD is not typically required for configuring your new MD series Power Meter for use with the Apogee or other Building Automation Systems. This metering kit, comprised of a meter plus three current transducers (CTs), has been factory-configured with meter setup parameters for the specific CT current ranges that were ordered.  

There are typically no additional user requirements that utilize the ViewPoint™ software to perform any further configuration of the MD series metering kits to support setup or installation. 

Please read the power meter installation chapter in the User Manual for the installation and start up instructions. If there is a reason to reconfigure the meter to accept a CT set with a different current range, please consult the appropriate Siemens MD series User Manual noted below.

To download the manual, click on the desired link:
•  Siemens MD-P1 and MD-P1D Series User Manual #125-201

2.  The MD-P1 and MD-P1D Power Meters have a fixed baud rate of 4800 baud.

image WARNING: Do not use the ViewPoint software tool to modify this P1 protocol fixed baud rate as it will make the MD-P1 Series power meter inoperable.

If this occurs, contact Siemens Building Technologies technical support for resolution at +1 (800) 877-7545, then select option #2 for technical support.

3.  The RS-485 network device address for the MD series Power Meters is set only via the rotary address switches on the front left face of the meter. The P1-FLN or BACnet/Modbus address cannot be configured with ViewPoint software. See the User Manual for detailed instructions on setting the device address via the front mounted rotary switches.

4.  If you intend to use the ViewPoint™ software tool with the MD series Power Meters for purposes of data register viewing or for firmware upgrades, please first consult the ViewPoint™ chapter in the User Manuals. 

image WARNING: Improper use of this powerful ViewPoint software tool may result in modifying internal meter setup parameters that could make the power meter inoperative.

Before using this ViewPoint software tool, please read the ViewPoint™ use instructions contained in the Siemens User Manual.  See links above to download the manual.

You may download a copy of this Read Me file by clicking here.

Software and Firmware Downloads
MD-P1, MD-P1D Series

ViewPoint Software Tool Downloads
•  Read Me
•  4-0-38 ViewPoint MD-Series.exe

MD Series 3-Phase Power Meter Firmware Downloads
To view a log of firmware update history, click here.

Current Firmware (for MD-BMS, MD-BMED Series Meters)
•  Firmware 4-82 MD-BMX.zip

--------------------------------------------------

MD-12HD, MD-48HD Networked Metering Systems
READ ME FIRST - MD-XXHD SERIES POWER METER STARTUP

info-symbol-small IMPORTANT! PLEASE NOTE:

1.  Please read the power meter installation chapter in the User Manual for the installation and start up instructions. TBD……….    

To download the manual, click on the desired link:
•  Siemens MD-12HD and MD-48HD Series User Manual #A6V11564207

2.  The RS-485 network device address for the MD series Power Meters is set only via the rotary address switches on the front left face of the meter. The BACnet/Modbus address cannot be configured with ViewPoint software. See the User Manual for detailed instructions on setting the device address via the front mounted rotary switches. See the MD-BMS  and MD-BMED User Manual for instructions regarding the setting of the IP address for the MD-BMED model Ethernet communication.

3.  If you intend to use the ViewPoint™ software tool with the MD series Power Meters for purposes of data register viewing or for firmware upgrades, please first consult the ViewPoint™ chapter in the User Manuals.

image WARNING: Improper use of this powerful ViewPoint software tool may result in modifying internal meter setup parameters that could make the power meter inoperative.

Before using this ViewPoint software tool, please read the ViewPoint™ use instructions contained in the Siemens User Manual.  See links above to download the manual.

You may download a copy of this Read Me file by clicking here.

Software and Firmware Downloads
MD-12HD, MD-48HD Series

ViewPoint HD Software Tool Downloads
•  Read Me
•  TBD

MD Series 3-Phase Power Meter Firmware Downloads
To view a log of firmware update history, click here.

Current Firmware (for MD-12HD and MD-48HD Series Meters)
•  TBD